Installation and model selection of mobile conveyor spreading treatment

Spreading treatment installation and model selection of mobile conveyors Spreading during operation of mobile conveyors is a common problem, and there are many reasons. The working principle of the mobile belt conveyor is that the driving device tensions the conveyor belt, and the middle frame and idler rollers form the conveyor belt as the traction and load-bearing components, so as to continuously convey the scattered materials or finished products. The problem of material spreading is not only that we only have to deal with it, but also related to the installation and model selection of the mobile conveyor. The issue of material spilling is also an issue that needs our attention. 1. Belt conveyor sprinkling treatment: (1) Sprinkling at the reloading point. The sprinkling at the reloading point is mainly in the drop hopper, guide trough, etc. For example, the belt conveyor is seriously overloaded, and the rubber skirt of the guide groove of the belt conveyor is damaged. The steel plate at the guide groove is designed to be far from the belt and the rubber skirt is longer to make the material rush out of the guide groove. The above situation can be solved by controlling the transportation capacity and strengthening the maintenance. (2) Spreading material when the concave section of the belt is suspended. When the concave section has a small curvature radius, the belt will be suspended. At this time, the belt groove will change because the belt has left the groove-shaped idler group. The angle becomes smaller, so that part of the material is scattered. Therefore, in the design stage, a larger radius of curvature of the concave section should be used as much as possible to avoid such situations. For example, in the mobile mechanical ship loader, stacker and reclaimer equipment, in order to shorten the tail car, the concave section here is designed as a non-arc transition zone. When the belt width is selected with a small margin, it is easier to spread the material. (3) Spreading when the belt is running deviation The spreading of the material when the belt is running is because the height of the two edges of the belt changes when the belt is running. One side is high and the other side is low. The material is scattered from the lower side. The processing method is Adjust the deviation of the belt. 2. Installation of mobile loading conveyor : (1) Before installation: install the belt conveyor after the transfer tower and silo are finished. (2) Precautions: The installation and adjustment of all belt conveyors are carried out in accordance with geological parameters and drawings. (3) Installation work: marking, checking civil construction, checking the condition of anchor bolts and embedded steel plates, checking the position of various parts of the belt loading conveyor, installing truss according to anchor bolts, installing and adjusting equipment (including upper and lower rollers, wipers , Drive device, etc.), install the belt lifter, install the telescopic head, install the guide groove, install the tension device, install all the electrical part brackets, tape cutting and vulcanization connection, work before the end of the installation (4) check: install the tape Check whether the belt conveyor is consistent with the drawings and geological graphics parameters. (5) Electrical part: install cable ducts, install limit switches, protection devices, electric control cabinets, etc., decorate lights, lay cables, and connect wires. (6) Painting: clean the damaged parts of the paint and paint in accordance with the technical specifications. . (7) Lubricating oil: Add grease or lubricating oil to the following equipment according to the procedures specified in the lubricating oil operation manual: reducer, coupling, crane, bearing seat, motor bearing, etc. 3. The choice of belt loading conveyor model: (1) The weight of the conveying objects (including the weight of the spreader), the external dimensions and the way of hanging; (2) The length and complexity of the line, that is, the horizontal turning section and the vertical bending The number of sections; (3) The environmental working conditions and work shifts of the conveyor; (4) The operating speed and productivity of the conveyor; (5) Special process requirements. So if the mobile conveyor you are using has a problem with material spilling, it may be that the machine needs to be repaired and replaced with new parts, but it is more likely that there is a problem in the installation process of your machine or it is simply your machine choice. There is a problem. The problem here is not the fault of the machine itself, but the model of the machine is not suitable for your needs. This kind of natural machine is not suitable for your use, and it is expected that this kind of problem will occur.

Ningbo YiFan Conveyor Equipment Co.，Ltd has an array of branches in domestic for servicing customers with high-quality products.

Crazy about products? Ningbo YiFan Conveyor Equipment Co.，Ltd is the place you must shop at, do visit YiFan Conveyor Equipment to check out our latest collections!

لكي يكون لديك شيء يتطلب الكثير من الحذر في التعامل معه، فمن الأفضل الاعتماد فقط على الموردين الموثوق بهم. Ningbo YiFan Conveyor Equipment Co.，Ltd can provide quality container loading machine flexible conveyor system that meet all your requirements for a while meet your individual needs.

Ningbo YiFan Conveyor Equipment Co.，Ltd are providing this to you at very low cost. إن مطالباتنا تعتمد فقط على ردود الفعل المختلفة التي تلقيناها من عملاء مختلفين وليس على الحكم الذاتي.

The first machine to produce container loading machine, the container loading machine gravity roller conveyor was invented in container loading machine in container loading machine by container loading machine and was subsequently improved